Kaypro 286 - Revision history

FrankRahman: /* Articles */

2026-06-05T22:04:23Z

Articles

← Older revision		Revision as of 22:04, 5 June 2026
Line 112:		Line 112:

	Chris Singleton has contributed significantly to this page.		Chris Singleton has contributed significantly to this page.

			==Technical Notes==
			<blockquote>'''KPC-286 CMOS ERROR FIX'''

			The following board modification will solve many of the PC286
			CMOS ram errors. Error indication is known by:<br>
			1. Repeated "INVALID CONFIGURATION, PLEASE RUN SETUP".<br>
			2. Audible error beep code of 1-1-3.<br>
			3. Will boot only after Ctrl-Alt-Del.<br>

			<p>The fix involves replacing R9 (a 1.2K Ohm resistor) with an 1N6263 Diode. Physical placement is opposite of CR2 (the cathode band is down toward the card edge contact fingers).</p>

			<p>Also the capacitor at C11 (upper right hand corner) must be
			changed from a 0.1uf to a .47uf capacitor. This help stabilize power supply voltage at DS1210.</p>

			<p>Technically the voltage difference between VCC (Power on) and
			battery voltage (Power off) at DS1210 is not great enough. Therefore the DS1210 cannot switch voltage source or enable the CMOS ram
			properly.</p>

			<p>By replacing the series resistor R9 with a series diode, the total battery voltage drop across both diodes (CR2 & the new one at R9) is increased by approximately .7 volt. This, in turn, increases the voltage potential difference at DS1210 assuring proper operation.</p>

			<p>Also, a 1 Meg resistor, watt, needs to be soldered from pin 2 to pin 5 at U5 on the backside of the board.</p>

			FROM: KAYPRO TECH SUPPORT

			ORIGINATOR: JOHN HILL</blockquote>

			<blockquote>
			'''CONTINUOUS RESET FAILURES'''

			Subject: PC286 and New 286i continuous RESET failures. 02/16/88<br>
			FROM Kaypro tech support

			RE: 3 Possible problems that cause continuous reset

			1. Improper setup can cause continuous reset. Make sure, by going
			through each and every parameter with the tech, that setup is
			correct. This would entail making sure all third party boards or drives are identified in setup.

			2. Certain 80286 processor chips, U10, are having heat related
			problems that cause a continuous state of reset or reset for a
			while and then lock up. The offending chips are AMD N80L286-12/S.
			AMD chips can easily be identified by a large arrow on the chip.
			These chips do not have a heat sink covering the chip so they are
			readily readable. We are also sending an Intel 80286 chip without
			a heat sink. (the AMD chip has Intel written on it for copywrite
			priveleges. Don't mix these chips up). The Intel chip works fine.
			We have AMD chips going out with a heat sink on the chip. These
			work fine also. The offending AMD 80286 chip without a heat sink
			has heat related problems. Spraying freon on the chip will make
			it work properly again, for a little while. The chips do not work
			in the temperature range they are specified to work in.

			3. They have found several 160 watt power supplys on the production
			line that are causing the continuing state of reset. It seems
			crosstalk between the +5 and +12 volt lines is causing this
			problem. If setup is correct and they do not have the offending
			amd chip, swap out the power supply.

			ORIGINATOR: JOHN HILL
			</blockquote>

FrankRahman: /* Articles */

2025-12-05T03:20:22Z

Articles

← Older revision		Revision as of 03:20, 5 December 2025
Line 99:		Line 99:
	"Kaypro Corporation recently introduced a 286		"Kaypro Corporation recently introduced a 286
	PC Card that, when exchanged for the 8088 card, enables the Kaypro PC to operate IBM PC/AT software. The "brain" of the 286 PC Card is an Intel 80286 CPU that utilizes the Kaypro PC's 16-bit potential. A trade-in allowance of $266 on your old 8088 card reduces the retail price of the 286 PC Card to $799, or $1065 without the trade-in."<br>		PC Card that, when exchanged for the 8088 card, enables the Kaypro PC to operate IBM PC/AT software. The "brain" of the 286 PC Card is an Intel 80286 CPU that utilizes the Kaypro PC's 16-bit potential. A trade-in allowance of $266 on your old 8088 card reduces the retail price of the 286 PC Card to $799, or $1065 without the trade-in."<br>
	(Kugram, ~~Sep~~-~~Oct 1985~~)		(Kugram, Jul-Aug 1986)

	"Kaypro also introduced a 20-MHz version of its Series 286. The EGA system comes standard with 1 megabyte of		"Kaypro also introduced a 20-MHz version of its Series 286. The EGA system comes standard with 1 megabyte of

FrankRahman: /* Articles */

2025-12-05T03:18:09Z

Articles

← Older revision		Revision as of 03:18, 5 December 2025
Line 97:		Line 97:

	==Articles==		==Articles==
			"Kaypro Corporation recently introduced a 286
			PC Card that, when exchanged for the 8088 card, enables the Kaypro PC to operate IBM PC/AT software. The "brain" of the 286 PC Card is an Intel 80286 CPU that utilizes the Kaypro PC's 16-bit potential. A trade-in allowance of $266 on your old 8088 card reduces the retail price of the 286 PC Card to $799, or $1065 without the trade-in."<br>
			(Kugram, Sep-Oct 1985)

	"Kaypro also introduced a 20-MHz version of its Series 286. The EGA system comes standard with 1 megabyte of		"Kaypro also introduced a 20-MHz version of its Series 286. The EGA system comes standard with 1 megabyte of
	RAM, a 40-megabyte hard drive, MS-DOS 3.3, GW-Basic, and Microsoft Works. The system will ship in 30 days and will cost approximately $4,000." (Infoworld, November 28, 1988)		RAM, a 40-megabyte hard drive, MS-DOS 3.3, GW-Basic, and Microsoft Works. The system will ship in 30 days and will cost approximately $4,000." (Infoworld, November 28, 1988)

FrankRahman: /* Articles */

2025-10-15T19:49:39Z

Articles

← Older revision		Revision as of 19:49, 15 October 2025
Line 100:		Line 100:
	RAM, a 40-megabyte hard drive, MS-DOS 3.3, GW-Basic, and Microsoft Works. The system will ship in 30 days and will cost approximately $4,000." (Infoworld, November 28, 1988)		RAM, a 40-megabyte hard drive, MS-DOS 3.3, GW-Basic, and Microsoft Works. The system will ship in 30 days and will cost approximately $4,000." (Infoworld, November 28, 1988)

			<blockquote>
			Kaypro controller Bob Gorski said the shortage of DRAMs, which allow computers to store information for quick retrieval, has caused prices of the chips available to increase to as much as $10 each, compared with $3 as recently as late January.

			The price increases have particularly hurt sales of Kaypro’s PC 286 model, a computer line introduced in December whose “guts” include 36 DRAMs. Despite the higher cost of the chips, Gorski said the PC 286 retail price has held steady at $2,995.<br>
			(LA Times, March 30, 1988)
			</blockquote>

	Chris Singleton has contributed significantly to this page.		Chris Singleton has contributed significantly to this page.

FrankRahman: /* Manual */

2025-09-15T19:42:01Z

Manual

← Older revision		Revision as of 19:42, 15 September 2025
Line 46:		Line 46:

	==Manual==		==Manual==
	[[~~File~~:Kaypro 286 manual.pdf]]		{\|
			\|-
			\| [[Media:Kaypro 286 manual.pdf\|Kaypro 286 Manual]] \|\|
			[[File:Kaypro 286 UG Cover.jpg\|200px]]
			\|}

	==Upgrading a Kaypro PC to a Kaypro 286==		==Upgrading a Kaypro PC to a Kaypro 286==

FrankRahman: /* Required Backplane (AKA Bus Board) */

2025-08-01T04:10:34Z

Required Backplane (AKA Bus Board)

← Older revision		Revision as of 04:10, 1 August 2025
Line 51:		Line 51:

	===Required Backplane (AKA Bus Board)===		===Required Backplane (AKA Bus Board)===
	Notice the ~~two~~ backplanes below. The upper one has 4 slots populated for 16 bit cards and 5 slots for 8 bit cards. The lower one is only setup for 9 slots of 8 bits each.		Notice the three backplanes below. The upper left one has 4 slots populated for 16 bit cards and 5 slots for 8 bit cards. The lower left one is only setup for 9 slots of 8 bits each. The right one has 2 slots for 16 bit cards and 7 slots for 8 bit cards.

	In order to take advantage of the 286's architecture the CPU card and other 16 bit cards need to plugged into the 16 bit slots.		In order to take advantage of the 286's architecture the CPU card and other 16 bit cards need to plugged into the 16 bit slots.
Line 61:		Line 61:
	\|		\|
	[[File:Backplane.jpg\|400px]]		[[File:Backplane.jpg\|400px]]
			\|\|
			[[File:Backplane 2-16bit.jpg\|400px]]
	\|}		\|}

FrankRahman: /* CPU board */

2025-07-31T19:41:06Z

CPU board

← Older revision		Revision as of 19:41, 31 July 2025
Line 44:		Line 44:
	[[File:286 cpu board.jpg\|600px]]		[[File:286 cpu board.jpg\|600px]]
	\|}		\|}

			==Manual==
			[[File:Kaypro 286 manual.pdf]]

	==Upgrading a Kaypro PC to a Kaypro 286==		==Upgrading a Kaypro PC to a Kaypro 286==

FrankRahman: /* Hard drive controller */

2025-07-15T03:26:19Z

Hard drive controller

← Older revision		Revision as of 03:26, 15 July 2025
Line 74:		Line 74:
	===Hard drive controller===		===Hard drive controller===

	"... the Kaypro 286 board will work with the very earliest PC-10s. Their hard disk controllers run at 5 MHz, while the upgrade boards use 10 and		"... the Kaypro 286 board will [not] work with the very earliest PC-10s. Their hard disk controllers run at 5 MHz, while the upgrade boards use 10 and
	12 MHz speeds. If your hard disk controller consists of two boards, one bolted to the hard drive and connected by cables to another in an expansion slot, you will have to change controllers before you upgrade."<br>		12 MHz speeds. If your hard disk controller consists of two boards, one bolted to the hard drive and connected by cables to another in an expansion slot, you will have to change controllers before you upgrade."<br>
	(Profiles, September 1988)		(Profiles, September 1988)

FrankRahman: /* Required Backplane (AKA Bus Board) */

2025-07-15T03:24:43Z

Required Backplane (AKA Bus Board)

← Older revision		Revision as of 03:24, 15 July 2025
Line 45:		Line 45:
	\|}		\|}

	==Required Backplane (AKA Bus Board)==		==Upgrading a Kaypro PC to a Kaypro 286==

			===Required Backplane (AKA Bus Board)===
	Notice the two backplanes below. The upper one has 4 slots populated for 16 bit cards and 5 slots for 8 bit cards. The lower one is only setup for 9 slots of 8 bits each.		Notice the two backplanes below. The upper one has 4 slots populated for 16 bit cards and 5 slots for 8 bit cards. The lower one is only setup for 9 slots of 8 bits each.

Line 69:		Line 71:
	(Profiles, July 1988)		(Profiles, July 1988)
	</blockquote>		</blockquote>

			===Hard drive controller===

			"... the Kaypro 286 board will work with the very earliest PC-10s. Their hard disk controllers run at 5 MHz, while the upgrade boards use 10 and
			12 MHz speeds. If your hard disk controller consists of two boards, one bolted to the hard drive and connected by cables to another in an expansion slot, you will have to change controllers before you upgrade."<br>
			(Profiles, September 1988)

	==Ads==		==Ads==

FrankRahman: /* Required Backplane (AKA Bus Board) */

2025-07-15T03:08:05Z

Required Backplane (AKA Bus Board)

← Older revision		Revision as of 03:08, 15 July 2025
Line 61:		Line 61:
	By upgrading to a processor board based on the 80286 microprocessor, you can effectively turn your computer into a fully functional AT-compatible if you have 16-bit slots. If you have 8-bit slots, you can still upgrade and achieve a degree of AT compatibly, but the shorter slots limit you. True AT compatibility requires that the computer read and write to external devices, such as AT hard disk controllers and extended memory boards, 16 bits at a time.		By upgrading to a processor board based on the 80286 microprocessor, you can effectively turn your computer into a fully functional AT-compatible if you have 16-bit slots. If you have 8-bit slots, you can still upgrade and achieve a degree of AT compatibly, but the shorter slots limit you. True AT compatibility requires that the computer read and write to external devices, such as AT hard disk controllers and extended memory boards, 16 bits at a time.

	The first Kaypro PC bus boards had 8-bit slots. In mid-1986 Kaypro switched to a bus board with two 16-bit slots, and as of this writing (April 1988) that board is still; being used. To reiterate, you can upgrade to an 80286 microprocessor even if you have 8-bit slots; but you are limited in your choice of expansion boards to those designed for PC and PC-XT compatibles.		The first Kaypro PC bus boards had 8-bit slots. In mid-1986 Kaypro switched to a bus board with two 16-bit slots, and as of this writing (April 1988) that board is still being used. To reiterate, you can upgrade to an 80286 microprocessor even if you have 8-bit slots; but you are limited in your choice of expansion boards to those designed for PC and PC-XT compatibles.

	If you are interested in obtaining a bus board that does have 16 bit slots, there are several courses open to you. First, you could go out and buy the necessary connectors and solder them in place, converting your old 8-bit board to a 16-bit		If you are interested in obtaining a bus board that does have 16 bit slots, there are several courses open to you. First, you could go out and buy the necessary connectors and solder them in place, converting your old 8-bit board to a 16-bit